SpotTEC - High-frequency Spot Generator
Tantec SpotTEC is used for treatment of profiles, cables and injection
moulded parts. The SpotTEC is easily adopted into any production
line and offers the user a high level of flexibility in use. The SpotTEC
is based on the principle of high-voltage discharge in atmospheric air
blown towards a substrate surface.
CableTEC – Corona Treatment of Cables
The purpose of surface treatment of polymer based materials is to
increase surface wettability through electrical discharge. The low
surface energy of polymer based substrates often leads to poor
adhesion of inks, glues and coatings. To obtain optimum adhesion, it
is necessary to increase the surface energy of the substrate to just
above that of the material to be applied. Surface treatment with
corona results in improved surface adhesion properties.
FoamTEC - Corona Treatment of Foam & Board
PP board is made of blended PP co-polymer and has one major
disadvantage - low surface energy, resulting in poor surface
adhesion for water-based adhesives and inks. Corona treatment
systems by Tantec significantly increase surface energy and
LabelTEC - Corona Treatment of Narrow Web
The purpose of surface treatment of polymer-based materials is
to increase surface wettability through electrical discharge. The
low surface energy of polymer-based substrates often leads to
poor adhesion of inks, glues and coatings. To obtain optimum
adhesion, it is necessary to increase the surface energy of the
substrate to just above that of the material to be applied.
Surface treatment with Corona results in improved surface
RotoTEC-X - Corona Treatment of 3-Dimensional Components
Tantec RotoTEC-X is used for in-line treatment of injection moulded
parts prior to coating, printing, gluing, painting etc. Often the
RotoTEC-X is also used simply for optimising adhesion properties
of a given substrate. The RotoTEC-X ensures a very uniform treatment
process and offers the user full process control of all parameters.
PipeTEC - Corona Treatment of Jacket Pipes
The PipeTEC is designed for treatment of the inside surface of jacket
pipes for optimised adhesion of PUR foam which is needed for
insulation of the pipe core. The PipeTEC must be fully integrated into
an extrusion line and ensures a very high level of surface treatment of
the entire inside surface.
MonTEC – Corona Performance Monitoring System
MonTEC is an advanced system for Tantec’s corona and plasma
treaters that monitors the discharge performance from each
individual treatment electrode.
SyrinTEC - Corona Treatment of Syringes
SyrinTEC is specially designed for 360° treatment of PP and PE
syringe barrels. Normally the SyrinTEC is built into the printing line
and positioned as the final process before the barrels enter into the
printing machine. Using the SyrinTEC enables treatment of the entire
outside surface without any inside treatment, which would increase
friction on the inside barrel and cause the plunger to drag when used.
NeedleTEC - Promotes Safer Needle Assembly
Single-use needles make up a significant percentage of the
disposable medical device market. Billions are produced annually, for
use in a wide variety of devices.
The OSHA-driven Needlestick Safety and Prevention Act requires
needle manufacturers to provide safer alternatives to existing
needle designs, resulting in hundreds of new designs annually. In an
attempt to comply with this act while remaining competitive in the
marketplace, manufacturers are exploring the uses of adhesives to
facilitate needle assembly.
PlasmaTEC-X – Atmospheric Plasma
Tantec’s New PlasmaTEC-X Atmospheric Plasma treatment system
is built around the concept of a high voltage DC Plasma discharge in
atmospheric air. The versatility of this unit allows for use in fully
integrated robotic cells, as a standalone unit, or most any
SpinTEC - Atmospheric Plasma treater
Tantec’s New SpinTEC Atmospheric Plasma treatment
system is built around the concept of a high voltage DC
Plasma discharge in atmospheric air. The versatility of this
unit allows for use in fully integrated robotic cells, as a
standalone unit, or most any production line.
ProfileTEC Plasma Treatment of EPDM Profiles
Two common applications for pre-treatment of automotive EPDM-
profiles with plasma are prior to flocking and slip-coating. In the
flocking process, treatment is necessary to achieve a strong bond
between the rubber and the adhesive used to attach the flock.
For slip-coating it is necessary to treat prior to the spray process
to achieve good wettability and optimum adhesion properties of
VacuLAB - Vacuum Plasma Treater for LAB Use
Tantec VacuLAB is a compact version of the full scale VacuTEC unit.
The VacuLAB offers the ability to handle small scale testing and of-
fers the user full control of all parameters. The results from using the
VacuLAB are easily transferred into full scale VacuTEC units.
VacuTEC - Vacuum Plasma Treater
Tantec ́s VacuTEC Plasma Treater is designed for treatment of a large
number of different injection moulded parts. The VacuTEC is available
with both single and multiple tray configuration. The VacuTEC offers
very fast treatment times and optimum adhesion properties for down-
stream coating, gluing, painting and printing applications.
VacuTEC-2020 - Vacuum Plasma Treater
Tantecs VacuTEC-2020 Plasma Treater is designed for treatment
of a large number of different injection moulded parts.
The VacuTEC offers very fast treatment times and optimum
adhesion properties for downstream coating, gluing, painting
and printing applications.
RotoVAC - Vacuum Plasma Treater
Tantec RotoVAC plasma treater is designed for plasma treatment of
small injection moulded plastic parts, without the need to place them
in a jig or use complicated handling systems. With the RotoVAC drum
design, simply fill the drum and place it in the vacuum chamber. The
rotation will ensure that all parts are treated.
VacuLINE - Vacuum Plasma Treater
The Tantec VacuLINE Plasma Treater is designed for treatment of a
variety of different injection moulded parts. The machine is ideal for
in-line production, where no operators are needed. The VacuLINE
system offers very fast treatment time and optimum adhesion
properties for downstream coating, gluing, painting and printing